5F

Carrier 5F compressor parts keep an old workhorse running. The Carrier 5F is an open-drive reciprocating compressor used in air conditioning and refrigeration, in belt-drive or direct-drive setups. CAP HVAC supplies aftermarket replacements for it across ten categories, from shaft seal assemblies and cylinder liners to bearings, crankshafts and valve plates. Match the failed part to a category below, then check it against your nameplate before you order.

What Makes the Carrier 5F Different From a Semi-Hermetic Compressor

On a semi-hermetic compressor, the motor sits inside the shell. On the 5F it doesn’t. The motor is mounted outside and connects by belt or direct coupling, which is why the 5F family is called open-drive.

That one design choice explains most of this page. A rotating shaft passes through the crankcase wall, so the shaft seal becomes a key wear item. The cylinders use replaceable liners. And because the motor is a separate piece, the compressor side can be serviced on its own. The 5F range covers roughly 5 to 25 nominal horsepower, with models such as the 5F20, 5F30, 5F40 and 5F60.

Aftermarket Carrier 5F Replacement Parts Made to Fit

A 5F that’s been in the field for years is usually worth repairing. Our Carrier 5F aftermarket parts are made to match original equipment specifications, so you can fix an older unit instead of replacing it. We’re based in Cleveland, Ohio, and we help customers around the country find the right part before they order.

Shop Carrier 5F Compressor Parts by System

Ten categories, grouped by what they do. Start with the one that matches your problem.

Carrier 5F Shaft Seal Assembly

The shaft seal is where an open-drive compressor is most exposed. It keeps oil and refrigerant inside while the crankshaft turns through it, hour after hour. When it wears, you’ll see oil weeping around the shaft or a slow loss of refrigerant charge. Don’t shrug off a small leak. Lost oil starves the bearings, and lost refrigerant costs you capacity. Replace the seal assembly as a set, and inspect the shaft surface it runs on while you’re there. The Shaft Seal Assembly category is the place to start.

Carrier 5F Cylinder Liner, Crankshaft, Bearing and C.R Bearing

These parts carry the load. Cylinder liners are replaceable sleeves, so a scored cylinder doesn’t have to end the compressor. The crankshaft turns on the main bearings, and the connecting rod bearings (listed as C.R Bearing on our site) sit where each rod meets the crank. Wear in one spot spreads to the next, so measure everything before you decide what to buy. Scoring, discolored metal or debris in the oil all mean you shouldn’t just swap one bearing and hope. Browse Cylinder Liner, Crankshaft, Bearing and C.R Bearing for the 5F.

Carrier 5F Oil Pump and Crankcase Heater

Two parts, one job: protecting the oil. The 5F uses a manually reversible oil pump, so rotation direction matters when you install it or reconnect the drive. Confirm the pump is set for your compressor’s rotation before the first start. The crankcase heater keeps liquid refrigerant from collecting in the crankcase during shutdown, where it would dilute the oil. If a unit sits idle for days at a time, a dead heater is a real risk. See Oil Pump and Heater.

Carrier 5F Valve Plate Assembly, Valve and Assembly and Gaskets

Worn valve plates cost capacity and push discharge temperatures up. Once the compressor is open you’ll want fresh gaskets anyway, so order them with the valve parts instead of after. The categories are Valve Plate Assembly, Valve and Assembly and Gaskets.

How to Match Parts to Your Carrier 5F Model

The 5F family isn’t one size, and a part that suits a 5F20 may not suit a 5F60. Here’s a quick way to get it right:

  1. Read the full model off the nameplate: 5F20, 5F30, 5F40 or 5F60, plus the rest of the model string.
  2. Note whether the compressor is belt-driven or direct-driven.
  3. Write down which part failed and what it was doing before it did.
  4. Compare all of that with the product page.
  5. If anything doesn’t line up, send us the model number and a photo of the old part.

Ten minutes of checking now saves a week of waiting on a return.

Why Buy Carrier 5F Compressor Parts From CAP HVAC

We’re an independent supplier of aftermarket HVAC and refrigeration compressor parts, and we sell to contractors, maintenance teams and distributors. The 5F range is sorted by component, so you can order a single seal or put together a longer repair list. Our catalog also covers other Carrier families, plus Copeland, Bitzer and Vilter. Questions about fitment or availability go to sales@caphvac.com or +1-855-612-3405.

FAQs

What is a Carrier 5F compressor?

It’s an open-drive reciprocating compressor for air conditioning and refrigeration, available in belt-drive or direct-drive setups and ranging from about 5 to 25 nominal horsepower.

What does open-drive mean?

The motor sits outside the compressor and turns the crankshaft through a belt or a direct coupling. The shaft passes through a seal in the crankcase, which is why the shaft seal assembly matters so much.

Why is my Carrier 5F leaking oil near the shaft?

A worn shaft seal assembly is a common cause, but gaskets can leak too. A technician should confirm the source before you order parts.

Are CAP HVAC parts original Carrier parts?

No. CAP HVAC sells independent aftermarket replacements that are compatible with the Carrier 5F. We aren’t affiliated with Carrier or any original equipment manufacturer.

How do I know a part fits my 5F?

Start with the model number on the nameplate and compare it with the product page. If you’re still unsure, contact us with the model number and a photo of the old part and we’ll help confirm the fit.

Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.