






















The 5H is a large open-drive reciprocating compressor used in air conditioning and refrigeration, rated from about 25 to 150 nominal horsepower. CAP HVAC supplies aftermarket replacements for it in more than twenty categories, from shaft seals and unloaders to pistons, crankshafts and valve plates. Find your category below, check the fit against your nameplate, and order.
Machines this size usually run something important: a cold storage room, a process line, a big building. When a 5H goes down, the clock starts. That’s why our Carrier 5H replacement parts are organized by component and made to original equipment specifications, so the part you order matches the one you pull out.
Many 5H units have decades of service behind them, and with the right parts there’s no reason they can’t have decades more. Our team in Cleveland, Ohio helps customers around the country identify the right part before they place an order.
Think of the 5H in sections: the drive end, the pump end, the crankcase, the cylinders, the capacity control and the valve end. Each section below lists its categories and links to the parts pages.
On an open-drive compressor, the shaft seal is the one component that has to hold pressure while something spins through it. Oil weeping at the shaft, or a slow loss of refrigerant charge, usually points here. Fix it early. A small leak is cheap to repair and expensive to ignore. The Shaft Seal Assembly category covers seal replacements for the 5H.
The pump end keeps oil moving to every bearing in the machine, and on a unit this size that’s a lot of bearings. The oil pump and the pump end cover do the work, the Impeller category sits alongside them for pump-end repairs, and the oil screen filters what the pump pulls in. If oil pressure is low and the level looks fine, check the screen first, then the pump. A scored pump or a damaged cover shows up as pressure that won’t hold. Browse Oil Pump, Pump End Cover, Impeller and Oil Screen.
This is the heart of the machine. The crankshaft turns on the main bearings, connecting rods link it to the pistons, and the connecting rod bearings (C.R Bearing on our site) carry the load at each journal. Big compressors tolerate wear well, right up until they don’t, so measure clearances before you order. If a journal is damaged, plan on replacing its bearing too. Reusing a bearing on a worn surface is how a repair fails a month later. See Bearing, C.R Bearing, Connecting Rod and Crankshaft.
Pistons and rings seal the compression chamber, and the pin and snap ring tie each piston to its rod. The snap ring is a tiny part with a big job. If one backs out, the pin can walk and score the cylinder wall, so it’s smart to use new ones whenever you reassemble. Compare ring condition against wear limits before you reuse anything. The categories are Piston, Piston Ring, Pin and Snap Ring.
A 5H doesn’t have to run flat out. As suction pressure changes, its capacity control reduces the compressor’s output, and Carrier says it can go as low as 35% of full design load. The unloader parts and springs make that happen. When unloading stops working, the compressor may run at full load when the system doesn’t need it, wasting power. If your 5H isn’t unloading the way it used to, start with the Unloader and Spring categories.
Gas comes in through the suction strainer, which catches debris from the system, and compression happens at the valve plate. Worn valves or plates cost capacity and push discharge temperatures up. Whenever the heads come off, new gaskets go in, and a clean strainer is cheap protection against whatever the system left behind. You’ll find them in Valve Plate Assembly, Valve and Assembly, Suction Strainer and Gaskets.
The crankcase heater keeps liquid refrigerant out of the oil during shutdown. Washers and other hardware are easy to forget until you’re mid-repair and one is missing, so add them to the order up front. See Heater and Washer.
The 5H family spans a wide range, with models such as the 5H40, 5H60, 5H80, 5H120 and 5H126, and parts for a small model rarely suit a large one. Before you order, read the complete model and serial number off the compressor nameplate. Work out which end of the compressor the failure is on, so you can go straight to the right category. If there’s a part number stamped on the old part, note that too. Still not sure? Send us a photo with the model number and we’ll help you confirm the fit before you buy.
CAP HVAC is an independent supplier of aftermarket HVAC and refrigeration compressor parts. We work with contractors, maintenance teams and distributors who need straight answers when a big compressor is down. The 5H range is sorted by component, and the same catalog carries other Carrier families, plus Copeland, Bitzer and Vilter. For fitment or availability, reach us at sales@caphvac.com or +1-855-612-3405.
It’s a large open-drive reciprocating compressor for air conditioning and refrigeration, ranging from about 25 to 150 nominal horsepower. The motor sits outside the compressor and drives it by belt or direct coupling.
It lets the compressor run at reduced capacity when demand drops, which saves power compared with running at full load all the time.
Both are open-drive compressors, but the 5H covers much larger capacities. Parts generally aren’t interchangeable between them, so match by model number. If you’re working on the smaller one, see our Carrier 5F parts.
No. CAP HVAC sells independent aftermarket replacements that are compatible with the Carrier 5H. We aren’t affiliated with Carrier or any original equipment manufacturer.
Start with the nameplate, then decide which end of the compressor failed and open that category. If you’re unsure, contact us with the model number and we’ll help narrow it down.
Product inquiries: info@caphvac.com
Sales inquiries: sales@caphvac.com
Product inquiries: info@caphvac.com
Sales inquiries: sales@caphvac.com
12901 Elmwood Ave, Cleveland, OH 44111, US
12901 Elmwood Ave, Cleveland, OH 44111, US
Disclaimer: All manufacturer names, symbols, and descriptions are used for reference purposes only. CAP HVAC is an independent supplier of aftermarket replacement parts and is not affiliated with, authorized by, or associated with any original equipment manufacturer (OEM). Parts supplied by CAP HVAC are compatible replacements and are not original OEM parts.